On film · 57 videos

See the tools at work

Most of what our instruments do happens inside a vacuum chamber, so we film it. Every video below was recorded through the microscope or at the bench — no renders.

Nanoprobing
PS8(e) probe tip and sample exchange guideProber Shuttle PS8e
PS8 Prober Shuttle packaging instructionsProber Shuttle PS8
PS8 Prober Shuttle — replace MM4 micromanipulatorProber Shuttle PS8
PS8 sample exchangeProber Shuttle PS8
Micromanipulators
MM3E — compucentric rotation of a microgripperMM3E
Three TEM lamellae lifted out in twelve minutesMM3E
Controlling the LiftOut Shuttle with iLOMM3E
MM3A-EM — micromanipulator for SEM/FIBMM3A-EM
Manipulating nanowires with two MM3A-EM micromanipulatorsMM3A-EM
Pick and place microspheresMM3A-EM
Nanowire micromanipulation in 3DMM3A-EM
MM3A-LMP — micromanipulator for light-microscopy probingMM3A-LMP
Plug-in Tools
Microgripper Plug-in for the MM3A-EMMicro Gripper MGS2
Microgripper Rotation imaged in 3DMicro Gripper MGS2
GIS-EM Plug-in for the MM3A-EM MicromanipulatorGas Injection System GIS
Charge Compensation inside an SEM using the GIS-EMGas Injection System GIS
Micro Injection System for ESEMMicroinjection System MIS
Substages
Anti Curtaining Table - Four-Axis Eucentric Tilt StageACT
Anti Curtaining Table (ACT) - four-axis substage for smooth cross sectioningACT
Anti Curtaining Table - milling 3D printed metalACT
ACT - Anti-Curtaining Table - mill sample while rocking back & forthACT
Configuring eucentricityACT
Eucentric Five Axis Tilting StageE5AT
Going Eucentric with the E5ATE5AT
Sample Exchange with the E5AT eucentric substageE5AT
Mounting a gripper to the E5AT (custom edition)E5AT
Two stacked 3-axis stages — 6-Axis Alignment Stage6-Axis Alignment Stage
Add-on Tools
EBIC and EBAC result overlaysEBIC Amplifier
Resistive contrast imaging (EBAC)EBIC Amplifier
EBIC at high bias voltagesEBIC Amplifier
Temperature-dependent fault isolationMicro Heating & Cooling Stage MHCS
Nanolathe animationNanolathe (RT-LATHE)
Nanolathe concentricity and tiltNanolathe (RT-LATHE)
Sharpening tips with the nanolatheNanolathe (RT-LATHE)
Concentric rotation made visible using frame integrationNanolathe (RT-LATHE)
Sharpening a copper postNanolathe (RT-LATHE)
SpringTable and Force Measurement Analysis software (STFMA)SpringTable & Force Measurement Analysis
In situ adhesion force measurementSpringTable & Force Measurement Analysis
SemCam — CCD camera for the SEMSemCam
Cryo Solutions
Cryo-FIB sample preparation for cryo-TEM using a cryo gripperCryo Lift-Out (CryoLO)
Life Science
Patch clamp experiment using the MM3A-LSMM3A-LS
Injecting dye into a cell with the MM3A-LSMM3A-LS
MM3A-LS for life-science applicationsMM3A-LS
Mechanical stimulation of biological samplesMM3A-LS
Software & Consumables
iLO - intuitive mouse control for TEM liftoutiLO Control Software
iLO software for MM3A-EM - compucentric rotation with RoTipiLO Control Software
SemGlu - a vacuum compatible, electron-cured adhesiveSemGlu
By application

Technique series

Nanoprobing
Failure analysis using in-SEM nanoprobing (FAMT 2021)Nanoprobing in the microscope
Analyzing a single TSMC 7 nm transistor — Part 1Nanoprobing in the microscope
Troubleshooting a TSMC 7 nm transistor short — Part 2Nanoprobing in the microscope
Probing Raspberry Pi 5 silicon with an electron microscopeNanoprobing in the microscope
Low-voltage EBIC investigation of fails (IPFA 2021)Nanoprobing in the microscope
Loading the PS8 Prober Shuttle on a Zeiss GeminiSEM 300Nanoprobing in the microscope
TEM Sample Preparation
TEM sample lift-out in a SEM/FIB using SemGluLift-out, filmed inside the chamber
TEM sample preparation in 3DLift-out, filmed inside the chamber
LiftOut Shuttle: LOS+ and TEM clip holdersLift-out, filmed inside the chamber
Mechanobiology
Microdissection of a chromosomeMechanical stimulation in action
Get in touch

Want to see it on your sample?

An application engineer can run your use case on our systems — live, or as a recorded session.

Get in touch